Abstract
In this work, we have synthesized crosslinkable and non-crosslinkable conjugated polymers for use in organic field-effect transistors (OFETs). Poly[4,8-bis(5-(2-ethylhexyl)thiophen-2-yl)benzo[1,2-b;4,5-b']dithiophene-2,6-diyl-alt-(4-(2-ethylhexyl)-3-fluorothieno[3,4-b]thiophene-)-2-carboxylate-2-6-diyl)] (PTB7-Th) and poly[[5-(2-ethylhexyl)-5,6-dihydro-4,6-dioxo-4H-thieno[3,4-c] pyrrole-1,3-diyl][4,8-bis[(2-ethylhexyl)oxy]benzo[1,2-b:4,5-b']dithiophene-2,6-diyl]] (PBDTTPD) are selected as our synthetic targets because these polymers have been used to fabricate high performing organic photovoltaics (OPVs) and OFETs. To synthesize crosslinkable polymers, 5 mol% of dibromo-cyclopentadithiophene (CPDT) which contains crosslinkable 1-hexenyl group is added as a monomer during polymerization. After the polymerization, Heck reaction is used to cap the allyl groups with 4-bromoanisole. Solubility of the crosslinkable polymers are tested after heating the polymer films at 160 °C for 16 hours. There are lots of insoluble particles which cannot be dissolved in chloroform. In order to discuss effects of the crosslinking on fundamental properties and OFET performances of the polymers, non-crosslinkable polymers (PTB7-Th and PBDTTPD) are also synthesized. Optical and electrochemical properties of the polymers are analyzed by UV-visible spectroscopy and cyclic voltammetry (CV). The crosslinkable polymers show very similar properties to non crosslinkable polymers, indicating that crosslink agent does not change the original optical and electrochemical properties. These polymers are used for OFET fabrication. non-crosslinkable PBDTTPD shows hole mobility of 2.9 x 10-5 cm2 V-1 s-1. After annealing at 180 °C for 1 hour, mobility is enhanced up to 5.3 x 10-5 cm2 V-1 s-1. Corresponding crosslinkable polymer Cr-PBDTTPD shows hole mobility of 5.6 x 10-5 cm2 V-1 s-1, which is changed to 9.4 x 10-5 cm2 V-1 s-1 after annealing at 160 °C for 1 hour. The device fabricated using PBDTTPD (annealed at 180 °C for 1 hour) shows high stability. This is due to crystalline nature of PBDTTPD. Lifetime of Cr-PBDTTPD device is improved a little by the crosslinking. PTB7-Th shows hole mobility of 3.1 x 10-3 cm2 V-1 s-1 which is higher than Cr-PTB7-Th (1.1 x 10-3 cm2 V-1 s-1). After annealing at 160 °C for 1 hour, Cr-PTB7-Th shows mobility up to 1.9 x 10-3 cm2 V-1 s-1. On the other hand, PTB7-Th shows mobility up to 3.6 x 10-3 cm2 V-1 s-1 after annealed at 180 °C for 1 hour. Furthermore, lifetime of Cr-PTB7-Th which was annealed at 160 °C for 1 hour is enhanced nearly 1.5 times compared to that of Cr-PTB7-Th before crosslinking. In addition, poly(triarylamine)s (PTAAs), which are known as a low cost and high performance polymers, are selected for the OFET lifetime measurement. PTAAs with various molecular weight are obtained via polyamination, followed by purification using preparative gel permeation chromatography and base treatment. Device stability of these PTAAs is compared. As a result, PTAA with base treatment shows highest mobility (1.1 x 10-4 cm2 V-1 s-1). X-ray photoelectron spectra are measured to investigate the chemical changes of various PTAAs.